682C03 振動トランスミッタ | PCBセンサ・オンラインストア東陽テクニカ

Model: 682C03
Platinum Stock Products: DIN rail mount vibration transmitter (for use w/ICP sensor), 4-20 mA outputs for vibration and temperature, 0-5/0-10 VDC output for vibration, raw vibration output, 3 Hz to 10 kHz frequency range

Specifications
アクセサリ
Product Documents

■ Specifications

Performance
Channels	1
Input Signal (Vibration)	±10.2 mV/(m/s²)	[8]
Input Signal (Temperature)	0 to 1.2 VDC	[5]
Output Signal (DC Vibration)	4 to 20 mA	[4]
Output Signal (DC Vibration)	0 to 5 VDC	[6] [9]
Output Signal (DC Vibration)	0 to 10 VDC	[6] [9]
Output Signal (Temperature)	4 to 20 mA	[5]
Output Signal (±0.01 %) (AC Vibration)	10.2 mV/(m/s²)	[1]
Frequency Range (-3 dB) (Acceleration)	3 to 10k Hz	[10] [11] [2]
Frequency Range (-3 dB) (Velocity)	3.5 to 10k Hz	[10] [11] [2]
Frequency Range (-3 dB) (Displacement)	3.5 to 1000 Hz	[10] [2] [3]
Output Range (DC Acceleration)	0 to 49.03 m/s² pk or rms	[7] [8] [9]
Output Range (DC Acceleration)	0 to 98.06 m/s² pk or rms	[7] [8] [9]
Output Range (DC Acceleration)	0 to 196.12 m/s² pk or rms	[7] [8] [9]
Output Range (DC Velocity)	0 to 12.7 mm/s pk or rms	[7] [8] [9]
Output Range (DC Velocity)	0 to 25.4 mm/s pk or rms	[7] [8] [9]
Output Range (DC Velocity)	0 to 50.8 mm/s pk or rms	[7] [8] [9]
Output Range (DC Displacement)	0 to 0.254 mm pk - pk	[7] [8] [9]
Output Range (DC Displacement)	0 to 0.508 mm pk - pk	[7] [8] [9]
Output Range (DC Displacement)	0 to 1.02 mm pk - pk	[7] [8] [9]
Environmental
Temperature Range (Operating)	-25 to 70 °C
Temperature Range (Storage)	-40 to 125 °C
Humidity Range (Non-Condensing)	0 to 95 %
Electrical
Power Required	DC Power
DC Power	23 to 25 VDC
DC Power (maximum)	100 mA
Settling Time	<2 min
Excitation Voltage (delivered to sensor)	17 to 19 VDC	[12] [13]
Constant Current Excitation (delivered to sensor)	3 to 5 mA	[12] [13]
Output Span (±5.0 %) (DC Vibration Current Output)	16 mA
Output Span (±5.0 %) (Temperature Output)	16 mA
Output Span (±5.0 %) (DC Vibration Voltage Output)	5 or 10 VDC	[9]
Physical
Electrical Connector (input/output)	Removable Screw Terminals
Electrical Connector (raw vibration output)	BNC Jack
Housing Material	Polyamide
Size - Height	99 mm
Size - Width	22.5 mm
Size - Depth	114.5 mm
Weight (Maximum)	127
Screw Terminal Wire Size	24-14 AWG
Din Rail Mount	35 mm
Status Indicator (Power "on")	Green LED
Status Indicator (Input Fault)	Red LED
Status Indicator (Measurement Mode - Acceleration)	Green LED
Status Indicator (Measurement Mode - Velocity)	Green LED
Status Indicator (Measurement Mode - Displacement)	Green LED

All specifications are at room temperature unless otherwise specified.

Product Notes

[1] Achieved with 100 mV/g ICP® accelerometer input.
[10] The low frequency tolerance is accurate within ± 0.5 Hz of the specified frequency.
[11] The high frequency tolerance is accurate within ± 0.5 kHz of the specified frequency.
[12] Jumper selectable for 18 VDC regulated, 24 VDC power supply voltage or ICP® sensor excitation disabled
[13] 4 mA constant current diode is internal to 9330VT
[14] See PCB Declaration of Conformance PS152 for details.
[2] Attenuation is -40 dB/decade.
[3] Maximum 1,000 Hz for displacement.
[4] Output current voltage will fluctuate at frequencies below 5 Hz.
[5] Requires use of accelerometer with "TO" temperature output option.
[6] Factory set, 0-5 VDC.
[7] Factory set, 1.0 in/sec peak
[8] Output measurement range is based upon input from 100 mV/g ICP® accelerometer and will be scaled inversely proportional to any percentage deviation of this input.
[9] Internal Dip switch selectable

Accessories:

No Accessories

Optional Versions:

No optional versions

■ Documents & Downloads

Product Documents

● Product Manual

● Product Specification Sheet