482D64 シグナルコンディショナ ICPセンサ対応| PCB製品・検索見積りサイト東陽テクニカ

Model: 482D64
4-channel, line-powered, ICP®/charge sensor signal cond., incremental gain, selectable charge conversion, TEDS, 10k LPF, USB, Ethernet

Specifications
アクセサリ
Product Documents

■ Specifications

Performance
Channels	4
Sensor Input Type(s)	ICP®, Voltage, Charge
Gain	x0.1 to x1000
Voltage Gain	x0.1 to x1000
Voltage Gain Increment	0.1
Accuracy (Gain, x0.1 to x0.4)	±5 %
Accuracy (Gain, x0.5 to x0.99)	±1 %
Accuracy (Gain, x1.0 to x1,000)	0.5 %
Sensitivity (±1 %) (Charge Input @ 100 Hz)	0.1 / 1.0 / 10.0 mV/pC
Insulation Resistance at Input (0.1)	> 10 kOhm
Insulation Resistance at Input (1.0)	> 100 kOhm
Insulation Resistance at Input (10.0)	> 1 MOhm
Input Range (Charge Input, Nominal)	±100000 pC
Output Range	±10 Vpk
Source Capacitance	<5nF	[4]
Frequency Range (-5 %) (>x100)	0.1 to 50,000 Hz	[5]
Frequency Range (-5 %) (x0.1 to x99.9 Gain)	0.1 to 100,000 Hz	[5]
Low Frequency Response (-5 %) (Charge Input)	0.5 Hz	[1]
Electrical Filter Roll-off	80 dB/decade
Filter Type (Fourth-order Butterworth)	Low Pass
Electrical Filter Corner Frequency (-3 dB)	10 kHz	[2] [3]
Electrical Filter Roll-off	24 dB/octave
Electrical Filter Pass Band Amplitude Accuracy	1 %
Electrical Filter Stop Band Attenuation (Minimum)	96 dB
Phase Response (at 1 kHz)	±1 °
Cross Talk (maximum)	-72 dB
TEDS Sensor Support	Yes
Fault/Bias Monitor/Meter (LED)	Open/Short/Overload
Linearity (Charge Input)	±1 % FS
Control Interface
Digital Control Interface	USB-C (2.0)
Digital Control Interface	Ethernet
Human Interface	Keypad
Display	2 rows, 16 columns
Digital Control: Cable Length (Maximum)	5 m
Environmental
Temperature Range (Operating)	0 to +50 °C
Electrical
Power Required (for supplied AC power adaptor)	AC Power
Power Required (direct input to unit)	DC Power
AC Power (50 to 60 Hz)	100 to 240 VAC
AC Power	1.6 Amps
DC Power	+9 to +18 VDC
DC Power	≤2.5 Amps
Excitation Voltage (To Sensor)	+24 VDC
DC Offset	≤50 mV
Constant Current Excitation (To Sensor)	0 to 20 mA	[7]
Output Impedance	≤50 Ohm
Discharge Time Constant (Charge Input)	1.0 sec
Broadband Electrical Noise (1 to 10000 Hz) (Gain x1)	17 µV rms	[6]
Spectral Noise (1 Hz ) (Gain x1)	1.0 µV/√Hz	[6]
Spectral Noise (10 Hz ) (Gain x1)	280 nV/√Hz	[6]
Spectral Noise (100 Hz ) (Gain x1)	200 nV/√Hz	[6]
Spectral Noise (1 kHz ) (Gain x1)	200 nV/√Hz	[6]
Spectral Noise (10 kHz ) (Gain x1)	200 nV/√Hz	[6]
Broadband Electrical Noise (1 to 10000 Hz) (Gain x10)	32 µV rms	[6]
Spectral Noise (1 Hz ) (Gain x10)	7.9 µV/√Hz	[6]
Spectral Noise (10 Hz ) (Gain x10)	630 nV/√Hz	[6]
Spectral Noise (100 Hz ) (Gain x10)	400 nV/√Hz	[6]
Spectral Noise (1 kHz ) (Gain x10)	350 nV/√Hz	[6]
Spectral Noise (10 kHz ) (Gain x10)	350 nV/√Hz	[6]
Broadband Electrical Noise (1 to 10000 Hz) (Gain x100)	180 µV rms	[6]
Spectral Noise (1 Hz ) (Gain x10)	750 µV/√Hz	[6]
Spectral Noise (10 Hz ) (Gain x100)	5.0 µV/√Hz	[6]
Spectral Noise (100 Hz ) (Gain x100)	2.5 µV/√Hz	[6]
Spectral Noise (1 kHz ) (Gain x100)	2.0 µV/√Hz	[6]
Spectral Noise (10 kHz ) (Gain x100)	2.0 µV/√Hz	[6]
Broadband Electrical Noise (1 to 10000 Hz) (0.1 mV/pC & Gain x1)	21 µV/rms	[6]
Spectral Noise (1 Hz) (0.1 mV/pC & Gain x1)	700 nV/√Hz	[6]
Spectral Noise (10 Hz) (0.1 mV/pC & Gain x1)	280 nV/√Hz	[6]
Spectral Noise (100 Hz) (0.1 mV/pC & Gain x1)	250 nV/√Hz	[6]
Spectral Noise (1000 Hz) (0.1 mV/pC & Gain x1)	220 nV/√Hz	[6]
Spectral Noise (10000 Hz) (0.1 mV/pC & Gain x1)	220 µV/√Hz	[6]
Spectral Noise (1 Hz) (1.0 mV/pC & Gain x1)	21 µV/√Hz	[6]
Broadband Electrical Noise (1 to 10000 Hz) (10.0 mV/pC & Gain x1)	26 µV rms	[6]
Spectral Noise (10 Hz) (1.0 mV/pC & Gain x1)	280 nV/√Hz	[6]
Spectral Noise (100 Hz) (1.0 mV/pC & Gain x1)	250 nV/√Hz	[6]
Spectral Noise (1000 Hz) (1.0 mV/pC & Gain x1)	220 µV/√Hz	[6]
Spectral Noise (10000 Hz) (1.0 mV/pC & Gain x1)	220 µV/√Hz	[6]
Spectral Noise (1 Hz) (10.0 mV/pC & Gain x1)	7.0 µV/√Hz	[6]
Spectral Noise (10 Hz) (10.0 mV/pC & Gain x1)	1.0 µV/√Hz	[6]
Spectral Noise (100 Hz) (10.0 mV/pC & Gain x1)	280 nV/√Hz	[6]
Spectral Noise (1000 Hz) (10.0 mV/pC & Gain x1)	250 nV/√Hz	[6]
Spectral Noise (10000 Hz) (10.0 mV/pC & Gain x1)	250 nV/√Hz	[6]
Calibration Input (±1 %)	±1000 pC/V
Overload Threshold (±0.2 Vpk)	+10 Vpk
Physical
Electrical Connector (ICP® Sensor Input)	BNC Jack
Electrical Connector (Charge Sensor Input)	BNC Jack
Electrical Connector (Output)	BNC Jack
Electrical Connector (DC Power Input)	6-socket mini DIN (female)
Electrical Connector (Charge Calibration Input)	BNC Jack
Electrical Connector (USB Digital Control)	USB-C
Electrical Connector (Ethernet)	RJ-45	[8]
Size - Width	20 cm
Size - Height	8.1 cm
Size - Depth	15 cm
Weight	1134 gm

All specifications are at room temperature unless otherwise specified.

Product Notes

[1] The low frequency tolerance is accurate within ±20% of the specified frequency.
[2] Frequency tolerance is within ± 5% of the specified value.
[3] Contact factory for other available frequencies.
[4] Maintain -5% amplitude up to 50k Hz response for all gain settings. High Frequency will be reduced for source capacitance >5 nF (Charge Input Mode)
[5] DC Coupling provide amplitude accuracy down to 0 Hz.
[6] Typical.
[7] User adjustable, factory set at 4 mA (± 1.0 mA). One control adjusts all channels.
[8] Auto sensing 10 base-T or 100 base-TX

Accessories:

標準付属アクセサリ

017AXX	電源ケーブル
100-7103-50
488B14/NC	ACアダプタ
EE75	コントロールソフトウェア

Optional Versions:

No optional versions

■ Documents & Downloads

Product Documents

● Product Manual

● Product Specification Sheet